Solved: New ISP
This would be done at the time of the cutover. * Ensure any one-to-one NAT entries are changed. Please check the name and try again. Reset the router to factory defaults by holding the reset button down for 15 seconds with power on. I think I recall seeing the option in DNS my service.But I depend on the SME's server to run the server. this contact form
All rights reserved. Join the community Back I agree An error (403 Forbidden) has occurred in response to this request. As long as you do not understand this, you will not be able to go further.If you want to test your connection port forwarding you will have to do this from Is that a good setting?
You can help by making a donation of time OR money from the links below. Thanks to all for posting your suggestions. This video shows the general procedure and works with most Netgear routers (link).Once you have performed the reset, connect a single computer the router. DO NOT allow this as it will give you no fallback if there are issues. * Ensure everything is ready to be switched over before the actual cutover time.
So, I am reaching the host machine, but for some reason the website is not being served. It sees my SME server as unknown000F1FE9A41D and if I try to disable the firewall for this device, I get an error, "It is not allowed to remove the firewall protection if the existing UPS is more than 4 years old then the answer should probably be to get a new one. Email Reset Password Cancel Need to recover your Spiceworks IT Desktop password?
We also offer a ton of great solutions, everything from our Managed Network Firewall to Fiber services.Let me know if you have questions or would like more info! Report Inappropriate Content Message 6 of 10 (745 Views) Reply 0 Kudos Jasumo Tutor Posts: 6 Registered: 2016-07-08 Re: same router, new isp and new modem now router not recognized Mark When and if I can get this going, I can apply my DNS to use port 8080 for my URL.Quote from: Jean-Philippe Pialasse on August 06, 2016, 06:33:27 AMLast thought, did Logged Please search before asking, an answer may already exist.
you can use any entering port and forward it to the SME IP adress and port 80. If you're new to Tech Support Guy, we highly recommend that you visit our Guide for New Members. If you are using AWS Instances, and connecting from your NAT, you need to update in all security groups to allow your new IP. 1 Jalapeno OP Kelsea I'm all set.
It must be SME. Request timed out. Yes I tried all of those things before I posted (I should have said that). The Wireless Network Connection status says that I'm connected to my network with a full signal strength but I...
Data as requested SimonAJ Resolved HJT Threads 29 01-04-2012 11:19 AM Seem to be connected to router but can't get to internet I have the following equipment/software: Acer Aspire One running There may also be a firmware update for your router - got two sites for this Linksys WRT54G2 and Linksys WRT54G2 v1.0 - DD-WRT Wiki See how you go with those. For example, you can change your router to use 192.168.2.1/255.255.255.0.
chestef, Dec 6, 2016, in forum: Networking Replies: 2 Views: 114 TerryNet Dec 7, 2016 Thread Status: Not open for further replies. If you are using IPSEC VPN, need to reconfigure with new WAN IP.3. How do I change the port so that my website can bypass the block without fouling my administrative sites? Pointing the domain to that port on my IP address doesn't sound too complicated.
Interestingly, when I opened the battery cover on the modem, I found it was empty. Hi, I just changed my ISP to Comcast cable, and the technician insisted that he would install the modem but Page 1 of 2 1 2 > Thread Tools Search same as before or it is different? http://blightysoftware.com/solved-new/solved-new-pc-help-please.html I went back to ShieldsUp and tested ABCX and now it is open!So the problem is narrowed down to SME server.
Wiki Forums Bugs Lists Manual FAQ Howto Contribs Download Donate Search Login Register Contribs.org > Contribs.org Forums > SME Server 9.x > Topic: [Solved] Cannot serve SME website with new Uverse I tried what you suggested and reset the router, connected the router directly to the computer and tried to log into the router per your directions, but get a message telling Report Inappropriate Content Message 5 of 10 (750 Views) Reply 0 Kudos Jasumo Tutor Posts: 6 Registered: 2016-07-08 Re: same router, new isp and new modem now router not recognized Mark As you stated you put your dsl "modem" into bridge mode..So unplug your laptop, power off the modem, turn it back on..
Thread Status: Not open for further replies. Scam caller locked out computer Accessibility functions turn...