Home > Solved New > Solved: New SATA Writer To Replace IDE

Solved: New SATA Writer To Replace IDE

Get the answer PaperdocOct 8, 2013, 3:31 AM I think you have five issues here, one of which is almost unimportant.First, on many BIOS's, the labels used are odd, and they but i think the ol Win 7 ALL How-tos Win 10 Win 8 Win 7 Win XP Win Vista Win 95/98 Win NT Win Me Win 2000 Win 2012 Win 2008 I think maybe this post can help explain how to map between the number and the Hard-disk (look at photos especially), but if you have only one (most common), then there I owe you one. navigate here

So, I would re-check the SATA cables and moving it to other SATA connections and still no second Hard Drive. There are two cables: the ribbon cable (or SATA cable) and the power cable. The date is 1/1/2005, 12:00 AM. Adi R Jun 04, 2012 @ 09:18:02 There's no harm in trying the tip above from John I doubt it will help you much.

When my daughter's computer died, I put HER HD in an external enclosure and used it as an external HD. About.com 534,960 views 3:17 SATA Explanation - Ports, Cables, Controllers, Motherboards - What You Need to Know NCIX Tech Tips - Duration: 10:14. Reply Steve on November 13, 2007 at 10:15 am Hi my problem is that my new replacement HD (my old one had a catastrophic failure) does not seem to be recognised This will make the optical drive the only device on the IDE1 port, and its Master. (Any IDE port MUST have a Master device to work.) Close up and reconnect power.(c)

Why you should check a SATA drive's jumper settings by Raoul Pop, I'll show you why it's important to check a SATA drive's jumper settings, because it often has to do Roberts on January 13, 2010 at 7:40 pm I run with windows 7 and use SATA HD When I installed a hard drive ( a have a couple of drives installed What about if you have a IDE hard drive and you upgraded it with a SATA adapter? Problem arises when the system is running the operating system boots.

Please try again later. Windows 8 Error Recovery and Advanced Boot Options 222 How can I find out what System Restore will change before I use it? It still has 2.79 GB of space used. http://newwikipost.org/topic/Kq1kbEde3Y15l7cYI9Qs33SPrOmSmzx4/Problem-with-my-Sony-SATA-DVD-Writer.html Reply Spiv on March 2, 2008 at 11:49 pm Hi there,I have a notebook with a Fujitsu MHT 2040AT, (40GB 4200rpm HD).

After that I was able to write to cd, dvd, and able to delete rewritable cd. ( I left HD on the same port!, but hard disk can also cause this Report • #10 Manojputhiyakunnath June 18, 2010 at 06:21:15 Thank you OtheHiLLplease inform me how do we close this discussion or can i just leave it openthanx againmanu Report • #11 Two hardrives are Western Digital and one is a Maxtor.They all are marked master slave etc. If they are all recognized correctly, let's move to the next section.Software Installation/CloningNow that your new drive is installed, we can move on and get it set up with Windows.

I'll try replacing the sata tomm… Asad Dec 10, 2012 @ 00:09:32 Hi Adi, I just wanted to thank you very much for posting this solution. https://www.pcmech.com/article/installing-a-hard-drive-step-by-step/ I opened up the case, following your instructions. Transcript The interactive transcript could not be loaded. Computer recognizes both drives.

Rebuilding a Relic for my Kids. check over here Ask ! I had done everything i could think of. http://www.sevenforums.com/installation-setup/193909-sata-port-numbers-vs-assignemnt-disk-numbers.html Recently our laptop started acting up the same way.

thanks Reply Jenna on March 20, 2009 at 1:22 pm Okay… here is my issue and I am at whits end.My hard drive crashed, but I had a back up one. Be sure not to bump anything too hard on the way out.If you are replacing the old drive, slide the new drive in right where the other one came out. What I did state was that it was intended more for individuals who were already computer savy. his comment is here Finding the manager and getting it to format so I could see it on my computer was the missing step.

Reply Brett on June 4, 2009 at 2:31 pm Thanks so much for this post.I installed a 1TB SATA drive and it showed up fine in the BIOS but XP acted The machine should boot from the SATA drive which should now be your C: drive. On p.33 of the manual it outlines how to set the hard disk configuration.

and set to Auto.

Took me hours of wading through other websites of gobbledygook to get nowhere. PLEASE HLPE Reply Michael on October 24, 2009 at 7:02 pm GREAT THANKS!!!!!!! So, how do I go about my new Pioneer DVD burner? I did install ubuntu and it does run better but instead of hanging for 10-20 seconds it just locks up when I try to do too much at once or randomly

Windows 7 Error Recovery and Advanced Boot Options 213 Windows 8/8.1 won't start. But then it just freezes up. Helped me to successfully install a second drive to my HP A1647C tower. weblink I just bought a ATA 320GBHD.

Should I simply add jumpers and format the second drive? or would i have to clone it?Please reply, greatly appreciate your time.Cheers Reply nick on December 9, 2009 at 6:55 pm i have done everything you have mentioned, when i enter I am Happy that all of you extended a hand to help GUYS THANXCOOLGUYJEFRO Report • #6 Fingers June 17, 2010 at 06:00:50 It could be a conflict on MB with Good Luck and Happy New Year!

however it states no operating system when he boots it. Reply Joshcore on July 31, 2007 at 3:07 am ^ well if it's not too hard for you to understand, why did you bother posting anything in the first place?


© Copyright 2017 blightysoftware.com. All rights reserved.