Home > Solved Pc > Solved: PC Must WARM UP Before It Will BOOT

Solved: PC Must WARM UP Before It Will BOOT

Step 3: Checking if the hard drive is detected in BIOS Perform the following steps to determine if the hard drive is detected in BIOS: Remove any media from the floppy I believe you have a separate vga card, not onboard otherwise you would not hear the 2 beeps. Report pd- Jul 16, 2009 at 10:16 AM Thanks. Multiple keyboards and mice take up more than just extra space, they make working a little more complicated. check over here

Report devonl- Nov 27, 2009 at 04:46 AM Awesome advice DJ Akshay, your advice worked perfectely - you saved me alot of money and frustration ! Step 5: Install the hard disk drive into another computer when troubleshooting the hard drive If another computer system is available, install the HDD as a data drive into the other Z7_3054ICK0KGTE30AQO5O3KA30H5 hp-country-locator-portlet Actions ${title} Loading... Would really appreciate it. read this article

The screen is blank. To me cold boot means the computer is completely off and has rested long enough to come down to room temps. I have made sure everything is plugged in, and tried plugging it into different outlets.

Report kshaun78› DJ AKSHAY - Oct 20, 2009 at 12:50 AM Dude I jst wanna say thanx. Give me the motherboard's model and everything which is written on your Processor. A recent hardware or software change might be the cause To resolve this error message and prevent it from occurring in the future, see Windows Error Recovery: Windows 7 failed to Sometimes when I try to start it up nothing comes on but the center fan on the metal prongs (the one that would run for only a few seconds) goes on

If I remove the memory cards, I should hear the beeps. Join the community of 500,000 technology professionals and ask your questions. Thank you again for taking the time to help so many people. (lurkers included). https://www.experts-exchange.com/questions/28352489/Hp-Computer-Won't-Boot-Until-Heated-with-a-Hair-Dryer-Why-And-CPU-Fan-Acts-Strange.html Try swapping the memory to another slot.

ouch! I believe you have got a new memory card so I understand that this cannot be faulty. Does that mean that my Motherboard is Dead>??? If still you get this hanging error then the memory card needs to be changed.

Plus remember correct bolts do not mean correct current (amps - in turn watts) Now while you are reading the second ref in section 2 there is a Power_Good text now http://superuser.com/questions/834134/processor-doesnt-heat-up-during-boot Any thing that expands with excess heat can cause a power to power or a power to ground short can cause this problem. A recent hardware or software change might be the cause. HELP ME PLEASE Report tusri› DJ AKSHAY - Oct 1, 2009 at 05:09 AM Dear DJ AKSHAY, I am facing the same problem .My machine started freezing on desktop screen during

I tried everything you posted and I haven't pinpointed the problem yet. check my blog Solved: PC must WARM UP before it will BOOT Discussion in 'Hardware' started by redhawk50, May 19, 2014. Did any one else have the same problem? Thanks :-) –bertieb Aug 17 '15 at 0:16 add a comment| up vote 0 down vote Since everybody here seems to be grasping at straws, here are my two cents: Try

Otherwise, continue to the next step of these instructions. Thankyou thankyou thankyou!! If still you do not hear a beep then I would suspect a motherboard failure. this content Why won't it do this when I restart the PC.

Report navyguy› DJ AKSHAY - Jan 16, 2010 at 11:18 AM ERASER TRICK WORKED FOR ME. Report Dara› DJ AKSHAY - Aug 5, 2009 at 11:21 AM DJ, you're the best! 4 months ago, I was switching the graphic cards on my PC. Report DJ AKSHAY 266Posts Sunday December 21, 2008Registration date April 26, 2010 Last seen - Feb 16, 2009 at 02:26 AM If you are getting access to the BIOS then the

Still had to hold down ctrl and alt.

We can't figure out which motherboard the computer uses. That was yesterday evening. F10 to save changes & exit BIOS then the PSU power cycles & the PC immediately restarts. Remove any hard drive screws that hold the drive to the chassis.

Enter the product key from the side panel of the computer. I even wait for 5 minutes and it's still on that screen. Country: United States Select a location Americas Europe, Middle East, Africa Asia Pacific and Oceania Select a language Confirm Back Z7_M0I02JG0KOT530A6KJKFRQ0816 hp-detect-load-my-device-portlet Actions ${title} Loading... have a peek at these guys I made triple sure that all connections are secure.

You should be able to see the requested info in the bios under hardware monitor or sometimes it is called health. Report sruman 5Posts Wednesday January 14, 2009Registration date January 31, 2009 Last seen - Jan 15, 2009 at 05:08 PM okay. Your computer might be different. My rule of thumb regarding the repair/replace value is between 50% and 75%: Unless the system is very valuable or otherwise irreplaceable, if the cost of repair is more than 50%

Normally under these circumstances we send them for repair. stat: modification timestamp of a file How can I get rid of "missing DLL" problems? And am maybe coming to the conclusion that it is a compatibility problem with my Intel i7-920 and my Asus rampage iii gene mobo. Status BAD, Backup and Replace To resolve SMART error messages, see Hard Drive Failure Errors.

As I said that one above is fine for what you have now. BSOD Help and Support Our Sites Site Links About Us Find Us Vista Forums Eight Forums Ten Forums Network Status Contact Us Legal Privacy and cookies Windows 7 Forums is an I was burning a cd with Nero, it stuck @ 5% and my computer was stucking... If the power adapter is still cold and the computer does not turn on, replace the power adapter.

When I switch on my system, the power light is on, the fan starts running and even the hard disk.


© Copyright 2017 blightysoftware.com. All rights reserved.